Another many article from the depths of Mr Asa. Thank you sir!
Sharpening your lawn mower blade is required maintenance, you gotta do this shit.Having a sharp blade will cut the grass easier, helps mulch the cut grass into smaller pieces, and a dull blade does damage to the grass such as tearing it out of the ground instead of cutting it cleanly.
Should do this a couple times a season, at the very least you should do it annually.
First things first, safety is important, gotta disconnect the spark plug. If you do this there's no possibility of the engine having a power stroke as you remove the bolt (in the next step), thus there's no possibility of you hurting yourself (unless you're really really bad with tools)
Next thing you need to do is remove the blade, so turn the mower over and find the proper socket size.
See the little lines around the perimeter of the head of the bolt? Those lines denote that it's a standard bolt, that means you'll need a standard wrench or socket. In this case you need a 5/8.
Now, you could use a ratchet for this, you could use a wrench...
But as our Prophet Tim said, "we need more power!"
As you can see, this blade has been beaten pretty bad, I've been neglecting it for a little while, but I hate this mower, so shit happens.
Ok, now you gotta get to work. Get to your work bench, put it in a vice. Don't have either of these? Send in your man card.
The dirtier your bench, the better.
Now, most people fuck up when they sharpen blades by reaching for a grinder. You don't use a fucking grinder on a blade, on any blade. You don't need to, it's complete overkill, and you can easily EASILY screw up the blade. Use a file, you have more control, and it does not take long.
Cleaning the blade to this point took maybe 10 minutes. The only real issues I have left on this side are the two nicks where my fingers are, and a very worn spot right in the middle. Another 5-10 minutes and these were gone.
You want to match the original edge as much as possible, it should be an angle of roughly pi/4
Gratuitous dude shot. Gotta keep the homos happy.
(fly edit:
)
Now, the point where you're done is A) when the blade is cleaned up completely, or B) when you pull a domon and hurt yourself. Happily for me, these came both at the same time. Personally, I don't wear Bitch Mittens, but safety gear such as gloves can help prevent issues such as this.
Now, two notes:
The way you know you're done is the blade is sharpened smoothly and completely, no more nicks, no more dull spots. The way you know that you need to take a break and sit down and watch some Spongebob is that you start getting sloppy with the file. The way that can tell that you're getting sloppy is that you don't have the same wear pattern on the material you're working.
It's a little hard to describe what I mean by this, so here's a couple pictures.
A normal sloppy wear pattern doesn't photograph very well, so I took a piece of aluminum and filed it down to an edge, then colored it. To show a bad wear pattern I filed it at a different angle. The sloppiness is revealed as two different patterns.
When you see this, you're getting tired, you need to go sit down and relax for a little bit. This goes the same for virtually anything tool related, when you recognize that you're getting sloppy, go take a break. When you recognize that you're getting tired and sloppy but don't take a break is when you get hurt.
Second note:
When working with a file, you want to start with a rough file. Rough files have relatively less teeth per inch but bigger teeth, so they cut more and cut faster, unfortunately as a result of this they leave a rougher, uglier edge.
Fine files have more teeth per inch that are smaller than rough files. They don't cut as much, but they create a much smoother, "prettier" edge.
You don't really need to use a fine file when you're doing work on something like this, fine edges are for delicate work such as chisels, rough edges are for tools that rely on a power stroke for them to do work such as axes, machetes, or lawn mower blades.
That being said, you can use a fine edge file on this to put a good edge on a lawn mower blade, but it won't last more than one trip around the yard, especially if you're hitting any sort of acorns or anything similar.
A fine file is in the background, a rough file is in the foreground.
Got an idea for an article of your own that we should hear about? Want free swag? Make a thread in the Article Submission forum or email it to [email protected]. If accepted, you'll receive a free tshirt!